IEC 60268-1 PDF

IEC SOUND SYSTEM EQUIPMENT – PART 1: GENERAL. Buy IEC Ed. Sound system equipment. Part 1: General from SAI Global. Buy IEC SOUND SYSTEM EQUIPMENT – GENERAL from SAI Global.

Author: Vule Vuran
Country: Jordan
Language: English (Spanish)
Genre: Science
Published (Last): 15 June 2006
Pages: 420
PDF File Size: 6.80 Mb
ePub File Size: 14.77 Mb
ISBN: 404-9-47069-509-4
Downloads: 62148
Price: Free* [*Free Regsitration Required]
Uploader: Tetilar

Methods for specifying and measuring general characteristics used for equipment performance. This sequence satisfies the requirements of Section 8.

BS 6840-1:1987, IEC 60268-1:1985

A special test signal “Program Simulation Noise”, whose spectral content is representative of music and speech. Along with listening tests SoundExpert performs objective measurements of audio devices and technologies. Methods for specifying and measuring general characteristics used for equipment performance Status: Crosstalk and radiation curves are then shown on the final display.

Your basket is empty. Software Requirements SoundCheck The sequence first plays a stepped sine through both channels of the DUT and captures the sound radiation from the DUT using 2 reference mics.

Worldwide Standards We can source any standard from anywhere in the world.

Band-limited version of square wave is used. First, a pink noise stimulus is played from the noise speakers and recorded by the unoccluded ears. Hardware Requirements In order to run the sequences, the following hardware is required: Noise speakers are set up adjacent to the HATS left and right ears. Once calibrated, position the microphones 0. Sound System Equipment — Part 7: T he new audio metric allows to measure waveform degradation using music as a test signal.

This sequence uses a pink noise stimulus kec characterize the passive, active and total attenuation of noise cancelling headphones.

The sequence prompts the operator to enter the rated voltage and lec impedance of the DUT. Calibrate the Headphone Amplifier channels per the instructions in the SoundCheck manual. Learn more about ifc cookies we use and how to change your settings. Verfahren zur Festlegung und Messung von allgemeinen Kennwerten fuer die Geraeteleistung.

  ESCALA DE BRESLOW PDF

BS EN adds an additional requirement – that the crest factor of ifc test signal the ratio between the instantaneous peak level of the signal and its RMS level be between 1.

This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3. It then enters a loop 602681- will run 5 times. Relink dialog Here is a list of sequences and their default signal paths unique paths are in bold: Calibrate the headphone amplifier channels per the instructions in the SoundCheck manual.

The user 602688-1 first prompted to enter the rated voltage. Take the smart route to manage medical device compliance.

Test signals used for objective measurements – SoundExpert

Connect the impedance boxes between the headphone amp out and headphone input. The Hz recorded time waveforms are processed using 06268-1 analysis to derive their fundamental values.

Headphones and Earphones is an international standard intended to characterize the performance of headphones and earphones.

No – I don’t want to receive the latest audio test information by email. The content you have requested is available uec to registered visitors. This is an even-only harmonics companion of standard triangle signal.

The faster, easier way to work with standards. It then calculates the voltage required to produce 1 mW into the rated impedance. If passive, connect to the headphone amp or separate audio power amplifier You are ready to start the sequence. The spectra are then power summed to derive a single SPL value and the Hz fundamentals are post processed to derive their SPL values.

Band-limited version of triangle wave is used. Please download Chrome or Firefox or view our browser tips. Find Similar Items This product falls into the following categories.

  HWZ MAGAZINE PDF

The standard itself is a lengthy document, 9 Sections and 3 Annexes covering 46 printed pages. The sequence then goes through a series of acquisition steps 602681- generate four fundamental curves which are then post-processed to calculate crosstalk.

The play and record acquisition takes place 3 times and the user is prompted to reposition the DUT on the HATS in between acquisitions. Search all products by. The sequence uses a stepped sine stimulus to measure frequency response, THD and impedance, a composite signal of 70 Hz and Hz with an amplitude ratio of 4: Below is a list of actual reference signals along with their time domain representation, frequency domain representation and Matlab code for their generation.

FebDecember 17, – 3: Oec following 35 tracks of various genres are used for objective measurements of audio equipment. We use cookies to make our website easier to use and to better understand your needs. A series of post processing steps calculates the attenuation curves, their average values and shows them on the final display.

Search results for “”

It can be created by passing pink noise through a special filter network defined in IEC It is recommended that the sequences be run directly from 602688-1 IEC folder.

A pink noise stimulus is played from the noise speakers and recorded by the occluded ears. Five separate sequences are provided, each designed to measure specific characteristics.