FT232R DATASHEET PDF

FTR USB UART IC Datasheet Version Clearance No.: FTDI# •. •. Neither the whole nor any part of the information contained in, or the product. FTDI FTRL: available from 8 distributors. Explore Integrated Circuits ( ICs) on Octopart: the fastest source for datasheets, pricing, specs and. FTRL Datasheet, FT FTDI USB to Serial UART IC Datasheet, buy FTRL USB to Serial UART IC.

Author: Jule Shajind
Country: Cuba
Language: English (Spanish)
Genre: Music
Published (Last): 22 December 2004
Pages: 174
PDF File Size: 8.46 Mb
ePub File Size: 7.11 Mb
ISBN: 501-3-53672-544-3
Downloads: 5741
Price: Free* [*Free Regsitration Required]
Uploader: Felar

With bus powered applications, the following should be noted: RS is a multi-drop network; so many devices can communicate with each other over a two wire cable interface. Values are shown for both a completely Pb free solder process i. Equivalent devices are available from Maxim and Analogue Devices.

Various 3rd party drivers are also available for other operating systems – see FTDI website www. This ensures that when both the SP transmitters and receivers are enabled then the device is active, and when the device is in USB suspend mode, the SP transmitters and receivers are datasheeet. Contact FTDI support for this service.

FTRL USB to UART Breakout Board

This allows the possibility of using the FTR in a dongle for software licensing. N either the whole nor any part of the information c ontained in, or the produc t des c ribed in this manual, may be adapted or re produc ed in any material or elec tronic form without the prior written c ons ent of the c opyright holder. Additionally, the UART signals can each be individually inverted and have a configurable high drive strength capability.

  ISO IEC 10118 3 PDF

Exceeding these may cause permanent damage to the device.

Packing codes for xxxx is: P lease refer to the block diagram shown in Figure 2. These characteristics ft232rr apply when an external oscillator or crystal is used. The pins are on a 0. It is recommended to ground the f2t32r heat sink area of the device. The value of the Ferrite Bead depends on the total current drawn by the application.

When supplied, the FTR is configured to use its internal clock oscillator.

This is a common feature of RS and requires the application software to remove the transmitted data from the received data stream. Low USB bandwidth consumption. Web based applications can be used to maintain product licensing this way. A suitable power switch IC for such an application is the Micrel www.

Can be used by an external device to reset the FTR. For details on how to use an external crystal, ceramic resonator, or oscillator with the FTR, please refer to Section 7. The above mecha nical drawing shows the SSOP package. For driver installation, please refer to http: Data packets can be sent to the device and they will be sequentially sent to the interface at a rate controlled by an internal timer equivalent to the baud rate pre-scaler.

New CBUS bit bang mode option. In-built support for event characters and line break condition. Y our s tatutory rights are not affec ted. Adjustable receive buffer datasheeg. The solder pads are on a 0.

All dimensions are in millimetres. When the USB host or hub is powered up an int ernal 1.

  2SA872 DATASHEET PDF

This example uses Sipex SP devices which have enables on both the transmitter and receiver. This number cannot be reprogrammed.

FT232RL USB to TTL Serial Module

Sys tem and equipment manufacturers and des igners are responsible to ens ure that their s ystems, and any Futu re T echnology D evic es I nternational L td FTDI devices incorporated in their datasheet ys temsmeet all applic able s afety, regulatory and s ys tem – level performanc e requirements.

No Supports bus powered, self-powered and high- USB specific firmware programming required. T his product or any variant of it is not intended for us e in any medic al appli anc e, devic e or s ys tem in whic h the failure of the produc t might reas onably be expec ted to res ult in pers onal injury. This mode differs from asynchronous bit bang mode in that the interface pins are only read when the device is written to. The FTR will fail to operate when the datashheet oscillator has been disabled, but no external oscillator has been connected.

FT232RL USB to UART Breakout Board

Refer to Section 3. A ll application-related information in this doc ument inc luding application descriptionss uggested FTD I devices and other materials is provided for referenc e only. Fully integrated clock – no external crystal, oscillator, or resonator required.