Small Spot/Mark (Separate Amplifier) Extremely thin beam ideal for detection of minute objects and marks. Order Omron Automation and Safety E3C-VS1G (ZND) at DigiKey. Check stock and pricing, view product specifications, and order online. Omron E3C-VS1G Photoelectric Sensor 10mm for E3C Amplifier: : Industrial & Scientific.

Author: Daigore Nesar
Country: Anguilla
Language: English (Spanish)
Genre: Health and Food
Published (Last): 21 March 2005
Pages: 432
PDF File Size: 10.49 Mb
ePub File Size: 3.12 Mb
ISBN: 961-9-30712-326-9
Downloads: 25406
Price: Free* [*Free Regsitration Required]
Uploader: Kajijind

Omron E3CVS1G Photoelectric Sensor, 10 mm Reflective, NPN Output

Please know and observe all prohibitions of use applicable to the products. The following measures can be taken to avoid mutual interference. Light may enter even if the Sensors are separated by more than the sensing distance.

Typical examples include the minimum sensing object, engineering data, step height detection data, and selection list for specifications. Lens and Case The lens and case of the Photoelectric Sensor are primarily made of plastic. Repeated Bending Normally, the Sensor cable should not be bent repeatedly.

Omron E3c-vs1g E3CVS1G Photoelectric Sensor Switch

Doing so may result in damage from burning and fire, particularly omton the liquid is flammable. The Reflector cannot be mounted if there is any oil or dirt remaining. Dirt should be gently wiped off with a dry cloth. Typical measures are as given in the following table. In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. Mutual Interference Mutual interference is a state where an output is unstable because the Sensors are affected by light from the adjacent Sensors.


Do not use it for such purposes. For this type of application, separate the Sensors by at least 1. If Sensors are mounted in opposite each other, slant the Sensors as shown in the following diagram. Be sure to read Safety Precautions on e3-vs1g 4. Placing them in the same conduit or duct may cause damage or malfunction due to induction interference.

Omron E3CVS1G Photoelectric Sensor, 10 mm Reflective, NPN Output Buy from Cross

Close mounting of Sensors is possible by alternating the Emitters with the Receivers in a zigzag fashion up to two Sensors. If copying or transmitting this catalog to another, please copy or transmit it in its entirety. Otherwise, it may malfunction or fail. Any exceptions to this rule are indicated in Safety E3c-vsg1 in individual product information.

When in doubt, special model numbers may be assigned to? Separate Sensors to distance where interference does not occur. These Sensors are designed for use in applications for sensing workpieces and workers that do not affect safety. Keep organic solvents away from the Sensor.

AC 2-wire Sensors Example: Exceptions are indicated in Safety Precautions in individual product information. Secure the connector cover by hand.


Cable diameter D3c-vs1g than 4 mm 4 mm or greater Tensile strength omfon N max. Use a soft, dry cloth to clean the Sensor. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: Insert a shield copper plate e3c-vs1b the Sensor and the noise source e.

Values Given in Typical Examples The data and values given as typical examples are not ratings and performance and do not indicate specified performance.

AC Two-wire Sensors Example: Ambient Conditions Do not use this Sensor in the following locations.

Use the following methods to attach and remove Fiber Units. Cable Bending Destruction Test Tough Wire Breaking Test With current flowing, bending is repeated to check the number of bends until the current stops. Omro catalog is protected by copyright and is intended solely for use in conjunction with the product.

Do not subject a shielded cable or coaxial cable to tension. If the Sensor does not operate, check the following points. Organic solvents will dissolve the surface.