QEA. ACTIVE. CDIP. J. 1. TBD. A N / A for Pkg Type. to QE. A. SNJAJ. QFA. ACTIVE. CFP. W. BCD to 7-Segment Decoder. General Description. The ‘LS48 translates four lines of BCD () input data into the 7-segment numeral code and provides seven. DATASHEET, This package accepts a positive-logic Binary Coded Decimal (BCD) input and converts it to the proper pattern necessary to.

Author: Sashicage Dirr
Country: Liberia
Language: English (Spanish)
Genre: Travel
Published (Last): 22 April 2011
Pages: 26
PDF File Size: 11.85 Mb
ePub File Size: 6.61 Mb
ISBN: 464-8-98959-527-3
Downloads: 41679
Price: Free* [*Free Regsitration Required]
Uploader: Kazizshura

Oct 6, 4. Feb 4, 4, Common cathodemeaning the negative connection of all of the LEDs is tied together.

using a decoder and 7 segment cathode | All About Circuits

Other than a little more conditional logic connections and a few more stages, there’s nothing stopping you from building a full digital clock with hours, minutes, and seconds. Yes, my password is: Oct 5, 3. D is the MSB of the digit. A PWM pulse-width modulated signal decoedr be applied to this pin to provided varying brightnesses to the LED display being driven, allowing user control of LED dimming for applications such as power 74448 by decreasing the brightness during times of low ambient light.

Discussion in ‘ The Projects Forum ‘ started by cjjgOct 5, A microcontroller can be programmed to perform the binary to decimal conversion and then use a look-up chart to perform the segment conversion.


74LS48 BCD to 7-segment Decoder Driver IC | Warefab

Your name or email address: To build a simple digital counter, consider using the decade counter. Finally, use combinations with AND gates to control the LT pin lamp test and zero blanking control RBI decodeg turn on all the leds or turn them all off at the desired numbers.

Jul 17, 22, 1, All segments are extinguished when a low logical zero signal is applied decode pin 4 OUT. However, if pins are limited on the microcontroller, it can be advantageous to use ICs in a multiplexing fashion to drive the 7-segment displays.

Read the datasheet for the pin configuration.


Oct 5, 1. The outputs are open-collector but have internal 2K ohm pull-up resistors and have a maximum low-level output sink current of 6 milliamperes 6mA.

The AND gates will take signal defoder the output of the counter or whatever drives the four inputs of the A high output is intended to light the segment. Can thermal cameras can be a beneficial tool for electrical engineers?

Wire the with the display as you would if you wanted to display all the numbers. The decimal point indicator on this volt-meter as well as the colons “: Shown above, is an example application of the 74LS48 7-seg decoder circuit.

7448 BCD to 7-Segment Decoder

This package accepts a positive-logic Binary Coded Decimal BCD input and converts it to the ddcoder pattern necessary to illuminate a 7 segment display. Oct 5, 2.


The potential for medical applications could be huge. Thermal Cameras for Electrical Engineers? Quote of the day.

In this decider, the microcontroller would send BCD binary coded decimal on 4 output pins to the chips. Embedded Systems and Microcontrollers. A discussion of Musk’s past success and future plans.

No, create an account now. Do you already have an account?

Oct 5, 2 0. A line selector an additional output line on the microcontroller could select which chip to target and cycle through the set of displays to produce the overall numeric output.

Pin – Function 1 – B input 2 – C input 3 – Lamp test input, hold low for normal operation 4 – RB output should normally read the same as RB input 5 – RB input This must be open no connection or held high 6 – D input 7 – A input 8 – Gnd 9 – e segment 10 – d segment 11 – c segment 12 – b segment 13 – a segment 14 – g segment 15 – f segment 16 – Vcc. You May Also Like: